home *** CD-ROM | disk | FTP | other *** search
/ Magnum One / Magnum One (Mid-American Digital) (Disc Manufacturing).iso / d22 / wd.arc / W3AH3 < prev    next >
Text File  |  1991-05-17  |  6KB  |  120 lines

  1.  
  2.      Western Digital is a registered trademark of Western Digital 
  3.      Corporation; IBM PC, AT and XT are registered trademarks of the 
  4.      International Business Machines Corporation; MS DOS, OS2 and PC DOS 
  5.      are registered trademarks of Microsoft Corporation.
  6.      
  7.                                    WD1003-WAH
  8.      
  9.                               Software Installation
  10.      
  11.      ...WARNING..................WARNING......................WARNING...
  12.      
  13.                     THE FOLLOWING LOW-LEVEL FORMAT PROCEDURE
  14.                     WILL DESTROY ALL DATA ON YOUR HARD DRIVE
  15.                       BACK-UP THE DATA ON YOUR DRIVE BEFORE
  16.                     CONTINUING WITH LOW LEVEL FORMAT ROUTINE
  17.      
  18.      
  19.      The format instructions that you follow are simple procedures to tell 
  20.      the computer that you have either one or two Winchester disk drives 
  21.      installed and prepares your operating system to recognize the Western 
  22.      Digital controller.  
  23.      
  24.      You will need to know the parameters of your hard disk drives.  As a 
  25.      convenience to you, we have included a list of the most common hard 
  26.      disk drives and their parameters.  To access this list, return to the 
  27.      previous menu.  If your drive is not listed, contact your drive 
  28.      manufacturer or consult your drive manual to determine drive type and 
  29.      parameters.
  30.      
  31.      1.   Insert your system Diagnostic Diskette (or equivalent).
  32.      
  33.      2.   Turn on power.
  34.      
  35.      3.   Boot diagnostic and select setup option.
  36.      
  37.      4.   Set clock, etc.
  38.      
  39.                                      CAUTION
  40.                      Avoid system damage by consulting your
  41.                      Technical Reference manual to ensure that your
  42.                      drive type is supported by your host BIOS drive
  43.                      tables.  Not all AT-compatibles share the same
  44.                      drive tables as IBM.
  45.      
  46.      5.   Select proper drive type.  (Consult your Technical Reference 
  47.      Manual.)
  48.      
  49.                                       NOTE
  50.      
  51.      Step 6 requires execution of low level formatting.  Use of the IBM 
  52.      Advanced Diagnostic (or similar program for IBM-compatibles) is 
  53.      necessary since these controllers contain no on-board Basic 
  54.      Input/Output System (BIOS) ROM.
  55.      
  56.      
  57.      6.   Insert your Advanced Diagnostic diskette and execute low level 
  58.      Format.  Follow instructions in your reference manual.
  59.      
  60.      7.   Insert System Diagnostic Diskette (or equivalent) after the 
  61.      system finishes the low level format.
  62.      
  63.      8.   Load and execute the FDISK (to partition your drive) and FORMAT 
  64.      (high level format) programs.  Follow instructions in your reference 
  65.      manual.
  66.      
  67.                                  Troubleshooting
  68.      
  69.      Problem:   1790 Disk 0 Error.
  70.      
  71.      Cause:     No low level format on hard disk.  Wrong drive type
  72.                 selected. Not enough drive power.  Bad cables. Improper
  73.                 drive selection or termination.
  74.      
  75.      Problem:   Drive does not partition.
  76.      
  77.      Cause:     Check drive types.  Note that drive types for the AT
  78.                 and AT-compatibles differ.
  79.      
  80.      Problem:   "Error Reading Fixed Disk" appears when booting from
  81.                 hard drive.
  82.      
  83.      Cause:     DOS partition not active.
  84.      
  85.      Problem:   Winchester activity LED continuously lit.
  86.      
  87.      Cause:     No problem.  Drive LED selected for latched mode.
  88.      
  89.      Problem:   For systems with two drives, both Winchester activity
  90.                 LEDs light at the same time.
  91.      
  92.      Cause:     Improper drive selection or termination. Inspect the 
  93.                 drive cables. If the data cables are straight, then set
  94.                 drive C's drive select switches for drive select 1 and
  95.                 drive D's drive select switches for drive select 2. If
  96.                 the data cables have a twist, set both drives' select
  97.                 switches for drive select 2. Consult your drive manuals
  98.                 or dealer for drive switch settings. Finally, under no
  99.                 circumstances, use twisted floppy cables for the
  100.                 Winchester drive. Floppy and Winchyester drive interface
  101.                 connections differ significantly.
  102.      
  103.                                        -2-
  104.      Problem:   Slow and inefficient operation.
  105.      
  106.      Cause:     The biggest culprit for this problem is an incorrect 
  107.                 interleave factor.  Therefore, some experimentation with
  108.                 the interleave factor may be necessary. (Refer to the
  109.                 format instructions for setting interleave factor).
  110.                 Interleave factors are very dependent on the host
  111.                 operating system and application.
  112.      
  113.      Problem:   Not getting full capacity from drive.
  114.      
  115.      Cause:     You may have an RLL type drive.  Consult your drive 
  116.                 manual.  The WD1003-WAH is designed for use with MFM
  117.                 type drives only.  DO NOT USE WITH RLL DRIVES.
  118.      
  119.                 
  120.